Vogelzang TR002B User Manual download pdf (Page 5)

TR002B | 20120125.0 www.vogelzang.com SHILOH™ | Page 5

ASSEMBLY INSTRUCTIONS

TOOLS AND MATERIALS REQUIRED

FOR INSTALLATION

TOOLS

• Pencil

• 6 foot Folding Rule or Tape Measure

• Tin Snips

• Drill: Hand or Electric

• 1/8˝ dia. Drill Bit (for sheet metal screws)

• Screwdrivers (blade and Phillips type)

• 10mm Nut Driver or Ratchet with 10mm Socket

• Safety Glasses

• Gloves

• 11/16 Socket or Wrench

MATERIALS

(NOTE: The following items are NOT included with your stove)

Flooring Protection: as speciﬁed (see page 7)

Chimney Connection: 6˝ dia. minimum 24 MSG black or 26 MSG

blue steel straight stove pipe or elbow(s) as required.

1/2˝ Sheet Metal Screws

Chimney: Existing 6˝ Code-approved Lined Masonry Chimney

or 6˝ Inside Dia. UL 103 HT (US)/ULC-S629 (CDN) listed

manufactured chimney.

Furnace Cement (manufacturer recommends Rutland Code 78

or equivalent)

CAUTION: STOVE IS HEAVY. MAKE SURE YOU

HAVE ADEQUATE HELP AND USE PROPER

LIFTING TECHNIQUES WHENEVER MOVING

STOVE.

1. Uncrate the stove and remove all cardboard and

styrofoam packing materials and protective poly

bag. Remove pedestal base, sides, front, top, ash-

drawer and ash drawer support from the carton.

(Save packing materials for further assembly.)

NOTICE: DO NOT remove ceramic blanket

material from inside stove pipe opening (Fig. 1).

This blanket provides an air seal on the side walls

of the stove to direct combustion gasses over the

secondary combustion tubes before exiting via the

4. Attach the pedestal front frame to the sides. The

pedestal front should go over (not inside of) the side

panels. Use three (3) self-tapping screws (provided

in the hardware pack) on each side to attach both

pedestal sides to the pedestal front (ﬁgure 4).

5. Position ash drawer support into assembled ped-

estal (Figure 5) and secure from rear with two (2)

machine screws, lockwashers and hex nuts. Tighten

all pedestal hardware.

6. Position the pedestal top with the large vent hole

positioned toward the front and attach with six (6)

chimney. DO NOT REMOVE the ceramic blanket

or your stove will not operate properly.

Figure 2 – Pedestal

Assembly Hardware:

sheet metal screws, 5/16˝

machine screw, lock

washer & hex nuts

Figure 3 –

Assemble

sides to base

Figure 4 –

Attach Pedestal

Front Frame to Sides.

(Note– front goes OVER

the side panels.)

Figure 1 – DO NOT remove ceramic blanket from

inside stove pipe opening. This is NOT packing

material but an integral component of the stove

combustion system.

NOTICE: Vogelzang International Corp. grants no warranty, stated or implied, for the installation or maintenance

of your wood stove and assumes no responsibility of any incidental or consequential damages.

2. Remove parts and hardware pack located inside

ﬁrebox.

3. Align the hole pattern of one of the pedestal sides

to the holes in the base and secure with four (4)

machine screws, lock washers and hex nuts. As-

semble the opposite side to the base. (Note: Sides

are interchangeable)

continued on next page

DO NOT

REMOVE!

1 2 3 4 5 6 7 8 9 10 ... 25 26

Comments to this Manuals

No comments

Vogelzang TR002B User Manual Page 5

Comments to this Manuals

Related products and manuals for Kiln Vogelzang TR002B