Vogelzang BX26E User Manual download pdf (Page 5)

VGZ-006 / 20120225.0 BX26E-STD / Page 5

ASSEMBLY INSTRUCTIONS

tools required

Safety Glasses

CAUTION: STOVE IS HEAVY. MAKE SURE YOU

HAVE ADEQUATE HELP AND USE PROPER

LIFTING TECHNIQUES WHENEVER MOVING

STOVE.

Refer to diagram and parts lists at back of this manual.

1. Uncrate the stove and remove packing materials

and protective poly bag. (Save exterior cardboard

box for further assembly.)

2. Remove parts from inside of stove. Parts

include: one swing top (#9), two lids (#10), one lid

support (#11) one damper collar (#13), one feed

door (#7), one lid lifter (#15), one slide damper (#5),

four legs (#1), hardware pack (#16), and S-Hook

(#17) from inside ﬁrebox.

3. Place ﬂattened carton on ﬂoor and carefully turn

stove over onto carton.

materials required

(NOTE: The following items are NOT included with your stove)

7. Carefully lift stove upright and place in desired loca-

tion (see following instructions for properly locating

stove).

Screwdrivers

(blade and Phillips types)

5/16” Nut Driver or Ratchet

with 5/16” Socket (for 1/4”

Hex Nuts)

11mm Nut Driver or

Ratchet with 11mm Socket

(for Stove Bolts)

Hearth Gloves

Pencil

6 foot Folding Rule or

Tape Measure

Tin Snips

Drill: Hand or Electric

1/8” dia. Drill Bit

(sheet metal screws)

Flooring Protection: 48˝ x 70˝ as

speciﬁed (see page 3)

Chimney Connector Pipe: 6˝

black steel (24 ga. min.) straight or

elbow (as required)

1/2˝ Sheet Metal Screws

Chimney: Existing 6˝ Lined

Masonry Chimney or 6˝ I.D.

manufactured chimney listed

to UL 103 HT.

Furnace Cement (manufacturer

recommends Rutland Code 78

or equivalent)

continued on next page

NOTICE: Vogelzang International Corp. grants no warranty, stated or implied, for the installation or maintenance

of your wood stove and assumes no responsibility of any incidental or consequential damages.

4. Attach the rear legs to base of stove with

long stove bolts (B), ﬂat washer (E) and hex nut (F).

5. Attach hearth to bottom

of stove with two short

stove bolts (A), wash-

ers (E) and hex nuts (F).

6. Attach the front legs to

hearth with long stove

bolts (B), ﬂat washers (E)

and hex nuts (F).

ill. A – Hardware Pack

ill. B – Rear Leg Assembly

8. Attach damper collar to rear top surface of stove

using short stove bolts (A) ﬂat washers (E) and hex

nuts (F).

9. Place swing top in po-

sition on top of stove.

To install, position at

approximately 45 de-

gree angle to stove

(dashed lines in ill. F)

until pins drop into lo-

cator holes then swing

into position.

10. Place lid support and

two lids in position on

swing top (see ill. F).

11. Place the slide draft into position on the

hearth. Hold in position with round head stove

bolt (C) and large ﬂat washer (D).

ill. C –

Hearth

Assembly

ill. D –

Front Leg

Assembly

ill. E – Damper Collar

1 2 3 4 5 6 7 8 9 10 ... 17 18

Comments to this Manuals

No comments

Vogelzang BX26E User Manual Page 5

Comments to this Manuals

Related products and manuals for Kiln Vogelzang BX26E